AC Power Sources Elgar and California Instruments Power Products Products | Support | Contact | News Sales Worldwide

California Instruments i/iX Series II : Specifications Operating Modes Model iX Series II i Series II Modes AC, DC or AC+DC AC or DC AC Mode Output Frequency Range: 16.00-1000 Hz (Note: Voltage on 300 V range derates from 300 Vrms max at 500 Hz to 150 Vrms max at 1000 Hz; See V-F rating chart. below) Total Power 3001i/iX: 3000 VA, 5001i/iX: 5000 VA, 9003i/iX: 3000 VA 3ø, with mode iX: 9000 VA 1ø, 10001i/iX: 10000 VA, 15001i/iX: 15000 VA, 15003i/iX: 5000 VA/ø 3ø, with mode iX: 15000 VA/ø 1ø Load Power Factor 0 to unity at full output VA AC Mode Voltage Voltage Ranges Range VLow VHigh AC 0-150 V 0-300 V AC+DC 0-150 V 0-300 V Load Regulation (with ALC on) < 0.2% Load Regulation (with ALC off) < 0.5% DC to 100 Hz, < 0.6% 100 Hz to 500 Hz in high voltage range, < 2.2% 100 Hz to 500 Hz in low voltage range, < 3% 500 Hz to 1000 Hz Line Regulation < 0.1% for 10% line change Output Noise (20 kHz to 1 MHz) < 250 mVrms typ., < 500 mVrms max. Harmonic Distortion (Linear) < 1% from 16 - 66 Hz, < 2% at 400 Hz, < 3% at 800 Hz (Full resistive load) DC Offset < 20 mV External Amplitude Modulation: Depth: 0 - 10 %, Frequency: DC - 2 KHz Isolation Voltage 300 Vrms output to chassis     AC Electronic Loads AC Modular Supply Discontinued Products Product Support Contact Sales     Service Agreement for all California Instruments AC except MX & FCS AC Mode Current Steady State AC Current Model 3001i /iX 5001i /iX 9003i /iX 3ø 10001i /iX 15001i /iX 15003i /iX 3ø 300 V range 11.1 18.5 11.1 /ø 37.0 55.5 18.5 /ø 150 V range 22.2 37.0 22.2 /ø 74.0 111.0 37.0 /ø Note: Constant power mode provides increased current at reduced voltage (See chart below) Peak Repetitive AC Current Model 3001i /iX 5001i /iX 9003i/iX 3ø 10001i /iX 15001i /iX 15003i /iX 3ø High range 96.0 96.0 96.0 /ø 192.0 288.0 96.0 /ø Low range 110.0 110.0 110.0 /ø 220.0 330.0 110.0 /ø Programming Accuracy Voltage (rms): ± 0.2 of range, 16 to 1000 Hz, Frequency: ± 0.01 % of programmed value, Current Limit: ± 0.5 % of programmed value, Phase: < 1.5° with balanced load at 50/60 Hz Programming Resolution Voltage (rms): 100 mV, Frequency: 0.01 Hz from 16 - 81.91 Hz, 0.1 Hz from 82.0 - 819.1 Hz, 1 Hz from 820-1000 Hz, Current Limit: 0.1 A, Phase, 0.1° Output Relay Push-button controlled or bus controlled output relay Output Impedance (iX Only) Programmable Z on 3001iX, 5001iX, 9003iX and 15003iX (3ø mode only) for 50 Hz fundamental Resistive Range: 17 - 1000 mOhm,resolution: 4 mOhm accuracy, 2 % FS Inductive Range: 230 - 1000 μH, resolution: 4 μH, accuracy: 2 % FS Measurements - Standard (AC Measurements) Parameter Frequency RMS Voltage RMS Current Peak Current Crest Factor Real Power Apparent Pwr Pwr Factor DC Voltage DC Current Power Range 16-500 Hz 0-300 V 0-40 A 0-120 A 0.00-6.00 0-6 kW 0-6 kVA 0.00-1.00 0-300 V 0-40 A 0-6 kW Accuracy* (±) 0.01% + 0.01 Hz < 100 Hz 0.5 V + 0.02% 0.5 A + 0.02% 0.5 A + 0.02% 0.05 10 W + 0.1% 10 VA + 0.1% 0.01 150 mV 70 mA 15 W 100 - 500 Hz 0.1 V + 0.02% 0.1 A + 0.02% 0.1 A + 0.02% 0.05 20 W + 0.1% 20 VA + 0.1% 0.02 150 mV 70 mA 15 W Resolution* 0.01 Hz 10 mV 1 mA 1 mA 0.01 1 W 1 VA 0.01 10 mV 1 mA 1 W * Measurement system bandwidth = DC to 48 kHz. Accuracy specifications are valid above 100 counts. Current and Power Accuracy specifications are times two for 10001i/iX /30003i/iX and times three for 15001i/iX and 9003i/iX and 15003i/iX with MODE-iX option when in single phase mode. For 10001i/iX, 15001i/iX and 30003i/ iX, resolution decreases by factor of 10, ranges for current and power increases by factor of three. PF accuracy applies for PF > 0.5 and VA > 50% of range. Measurements - Harmonics Parameter Frequency Fundamental Harmonics Phase Voltage Current Range 16.00-500.0 Hz / 32.00 Hz - 48.00 kHz 0.0 - 360.0° Fundamental Harmonics 2 - 50 Fundamental Harmonics 2 - 50 Accuracy* (±) 0.01% + 0.01 Hz 2° typ. 250 mV 0.1% + 250 mV+0.1% /1 kHz 50 mA/0.1% + 50 mA +0.1% /1 kHz Resolution 0.01 Hz 0.5° 10 mV / 10 mV 10 mA / 10 mA * Accuracy specifications are valid above 100 counts. Accuracy specifications are times three for three phase mode. Harmonics frequency range in three phase mode is 32 Hz - 16 kHz. Resolution decreases by factor of 10 for 9003iX and 15003iX with Mode-iX option in 1 phase mode and for 10001iX, 15001iX and 30003i/iX. DC Mode Output Power (Max at full scale of DC Voltage Range) 3001i/iX: 2100 W, 5001i/iX: 3500 W, 9003i/iX: 2100 W/ø 3ø, 6300 W/ø 1ø, 10001i/iX: 7000 W, 15001i/iX: 10500 W, 15003i/iX: 3500 W/ø 3ø, 10500 W/ø 1ø Voltage Ranges Range: Low: 200 Vdc, High: 400 Vdc Line Regulation < 0.1% FS or 10% line change Output Noise < 250 mV rms typ., < 500 mV rms max., (20 kHz to 1 MHz) Max DC Current (Maximum current at 65% of V Range): Model 3001i /iX 5001i /iX 9003i /iX 9003i /iX 3ø 10001i /iX 15001i /iX 15003i /iX 3ø 400V range 7.8 13 23.4 7.8 26 39 13 200V range 15.6 26 46.8 15.6 52 78 26 Current Limit Programmable from 0 A to maximum current for selected range AC+DC Mode Output Output Power (iX only) Full AC Power if DC component is less than 20% of full scale voltage, Full DC power if DC component is above 20% Storage Non Volatile Mem. storage 16 instrument setups, 200 user defined waveforms Waveforms Waveform Types i Series II: Sine, iX Series II: Sine, Square, Clipped sine, User defined User defined waveform storage Four groups of 50 user defined arbitrary waveforms of 1024 points for a total of 200 (One group can be active at a time) System Interface Inputs Remote shutdown, External Sync, Clock/Lock (option) Outputs Function Strobe, Clock/Lock (option) Protection Over Load Constant Current or Constant Voltage mode Over Temperature Automatic shutdown Remote Control IEEE-488 Interface IEEE-488 (GPIB) talker listener. Subset: AH1, C0, DC1, DT1, L3, PP0, RL2, SH1, SR1, T6, IEEE-488.2 SCPI Syntax RS232C Interface 9 pin D-shell connector, Handshake: CTS, RTS, Data bits: 7,8, Stop bits: 1, 2, Baud rate: 9600, 19200, 38400, 57600, 115200, IEEE-488.2 SCPI Syntax (Supplied with RS232C cable) DC Mode Output Voltage 3001 and 9003: 208-240 ± 10% Vac, (L-N, 1ø), All other models: Standard: 208-240 ± 10% Vac, (L-L, 3ø), Option -400: 400-480 ± 10% Vac, (L-L, 3ø) (Input range must be specified when ordering) Max DC Current (Maximum current at 65% of V Range): Model 3001i/iX 5001i/iX 9003i/iX 10001i/iX 15001i/iX 15003i/iX 187-264V 25 A 23 A 75 A 46 A 69 A 69 A 360-528V N/A 12 A N/A 24 A 36 A 36 A Inrush Current per chassis < 100 Apk for 100 μs at 208-240 V, < 50 Apk for 100 μs at 400-480 V Line Frequency 50-60 Hz ± 10 % Efficiency 75% typical Power Factor 0.6 typical AC Service Regulatory IEC61010, EN50081-2, EN50082-2, CE EMC and Safety Mark requirements RFI Suppression CISPR 11, Group1 , Class A Rear Panel Connectors AC Input & Output terminal block with cover, IEEE-488 (GPIB) connector (rear panel), 9 pin D-Shell RS232C connector*, Remote voltage sense terminal block, System Interface Connector, *RS232 DB9 to DB9 cable supplied Physical Dimensions Dimensions Height: 7” (178 mm), Width: 19” (483 mm), Depth: 24” (610 mm) (depth includes rear panel connectors) Weight per 5001i/iX Chassis: Net: 61 lbs / 28 Kg, Shipping: 115 lbs / 52 Kg Vibration and Shock Designed to meet NSTA project 1A transportation levels Air Intake/Exhaust Forced air cooling, side air intake, rear exhaust. Operating Humidity 0 to 95 % RAH, non condensing. Temperature Operating: 0 to 40° C, Storage: -20 to +85° C

Copyright © 2010 AMETEK Inc. Privacy Phone: 858-450-0085